HM Extruder and Gusseting Machine

We are looking for HM extruder and gusseting machine as follows:
- Width of extruder: 25" to 30"
- With a die of LD for extrusion of LD
- Acceptable age: 5 to 7 years old
- The machine must be in

For more details on HM Extruder and Gusseting Machine click here

10 inch PTI Trident Extruder

Model: 10000
- 10:1 L/D
- Electrically heated, water cooled barrel with circulation system
- Flender gear box with 17.423:1 ratio
- 100 rpm, 250 hp DC motor with SCR controller
- Control panel wi

For more details on 10 inch PTI Trident Extruder click here

PTI Trident Series 5 inch 28:1 Extruder

Used PTI model 5000 Trident series 5" 28:1 extruder includes:
- 5-zone electrically heated air cooled barrel at approximately a 55" centerline height.
- Gearbox is a flenders type SZNF-320, has a rreduction ratio of 17.

For more details on PTI Trident Series 5 inch 28:1 Extruder click here

2.5" Davis Standard Thermatic Extruder

Model: 25IN25
- L/D: 30:1
- 6 barrel zones
- Air cooled, vented and plugged
- Reliance DC motor 75 hp with Tachometer
- 1750 motor RPM, 127 amp.
- Belt driven
- Gearbox ratio: 11.06:1
- 100

For more details on 2.5" Davis Standard Thermatic Extruder click here

Leistritz Extruder

Type: ZSE110 / 2M
- Working hours: 15,975 hours
- Screw: Twin screw, 110 mm, counter rotating, 5 to 80 RPM
- L/D: L = 20D
- Engine: 110 KW, 0 - 2300 RPM
- Capacity: Up to 500 kg / hour
- Tempera

For more details on Leistritz Extruder click here

4.5" Sterling Extruder for Recycling

Used 4.5" Sterling Extruder
- L/D ratio: 34:1
- Direct driven 400 hp DC motor, 1750 RPM, 629 amps,
- Sabina DC drive control
- Gear box ratio: 11.4:1
- 6 zones, water cooled barrel
- Vented witth vacuum pump
- Temperature control panel with 9 eurotherm ETH3 controls and 4.

For more details on 4.5" Sterling Extruder for Recycling click here

57mm Werner & Pfleiderer Twin Screw Extruder

Used Werner & Pfleiderer 57mm co-rotating twin screw extruder
Model: ZSK57W50P8N
- Driven by a 100 HP DC motor
- Has 3.015/1 gearbox ratio
- Supplying 580 rpm screw speed
- Has (8) barrel secti

For more details on 57mm Werner & Pfleiderer Twin Screw Extruder click here

85 mm Luigi Bandera Single Screw Extruder

Model: TR.85AFT/30D
- L/D: 30:1
- 100 KW motor
- Air cooled, electric heated ceramic bands
- 5 barrel zones, with 11 temperature controllers and motor drive
- Was running HDPE pipe

(For images

For more details on 85 mm Luigi Bandera Single Screw Extruder click here

2.5" Davis Standard Extruder

Model: Thermatic 25IN25HT
- L/D ratio: 30:1
- Gear box ratio: 17.26/1
- Belt driven
- 40 hp GE Kinamatic DC motor with cutler hammer responder drive control
- 75 hp gear box capacity
- 1.25 serv

For more details on 2.5" Davis Standard Extruder click here

10 inch Farrel Hot Feed Extruder

Used 10" 9/1 Farrel hot feed extruder.
- Pneumatic ram with 32" long oversize feed throat.
- Previously used as dump extruder from Farrel F-80 banbury mixer.
- Hanson gearbox with 17.859/1 reducction ratio rated at 450 hp at service factor of 1.

For more details on 10 inch Farrel Hot Feed Extruder click here