Used 10" Farrel Dump Extruder

- 7:1 L/D
- 48" long jacketed barrel
- 28" feed section with pneumatic stuffer
- Cored screw with rotary union, model 2V gear box. 17.804:1 gear ratio. Gear box rated at 450 hp, less motor.
- Geear box reconditioned in 1991.

For more details on Used 10" Farrel Dump Extruder click here

Buss Extruder

Brand: Buss
- Type: APC70
- Screw: Single screw, 70 mm
- L/D: L = 13D
- Engine: H7/R20

Including:
- Brabender DDS40 twin screw side feeder
- MAAG Melt pump MPD 45/45 extrex
- Cooling equipme

For more details on Buss Extruder click here

Plastic Extruders for Pelletizing

We have 2 identical never used plastic extruders.
- Single screw 60mm X 30:1,
- 30 hp 480 V 60 Hz motor
- 5 station 480 V electric heaters
- 1 screw is configured for polypropylene
- 1 screw co

For more details on Plastic Extruders for Pelletizing click here

APV Sterling Extruders

a) 6" APV Sterling Extruder
- 32:1 L/D
- Electrically heated
- Water cooled barrel with circulation system - Jacketed feed section
- 68" center line height
- 400 hp dc motor with scr controlller
- 17.

For more details on APV Sterling Extruders click here

Lab Extruder

We are looking for Lab Extruder as follows:
- Barrel diameter: 20 mm
- L/D: 42 to 44
- Motor rating: 7.5 KW
- Screw: 1200 RPM
- Volumetric feeder - 1 no.
- Material to be process: PA6, 66, POM,PPBT, PMMA, ABS, GPPS, HIPS, PP, PC etc.

For more details on Lab Extruder click here

Vent 150HP Merritt Davis DC/SCR

Description:
- Used 8" Merritt Davis 12/1 L/D hot feed extruder.
- Has electrically heated water cooled
- Vented/plugged barrel 103" long from front of oversize feed
throat.
- Feed throat is 299" x 34" with ram assist.

For more details on Vent 150HP Merritt Davis DC/SCR click here

8" Black Clawson 24/1 L/D Non-vented Extruder

- New barrel and screw installed spring 2003.
- Extruder originally new 1964
- New Hanson gearbox installed 1999
- Gearbox rated 1120 hp with safety factor of 2.8/1 and 16.011/1 ratio, designed foor direct connected motor
- No temperature panel, or motor included (available at additional cost)
- Has electrically heated water cooled barrel with cast aluminium heaters installed new 1997
- Has 11" x 14" feed throat water cooled, and water cooled screw with rotary union
- It was last in use by 3M as an extruder for a PP film line.

For more details on 8" Black Clawson 24/1 L/D Non-vented Extruder click here

Delhi make LDPE Extruders

- No. of machines: 2
- Die size: 8" and 7"
- Screw size: 55 mm
- Blower speed: 2,800 rpm
- Motor size: 15 HP (AC Drive)
- Haul off rotation: No
- Screen changer: Manual
- Take up roller width: 36 inches
- Nip roller width: 36 inches
- Guard roller width: 36 inches
- Gear box ratio: 10:1
- Tubing size: 10 to 30 inches
- Film thickness: 17 to 50 micron
- Output: 30 to 35 kg/hr.

For more details on Delhi make LDPE Extruders click here

Windsor LDPE Extruder

- Die size: 7"
- Screw size: 55 mm
- Blower speed: 2,800 rpm
- Motor size: 15 HP (AC Drive)
- Haul off rotation: Yes
- Screen changer: Semi auto
- Take up roller width: 33 inches
- Nip roller wwidth: 29.

For more details on Windsor LDPE Extruder click here

100 mm Extruder

We are looking for an extruder as follows:
Approx. 100 mm screw
- 500-600 mm die
- IBC cooling
- Gusset boards
- 1800 mm wide haul off and take off or above
- Single station winder


For more details on 100 mm Extruder click here

150 mm NRM PS and PP Extruder

- Screw and barrel checked by specialist
- Gearbox checked and fit new oil seals.
- Motor overhaul, refitted and aligned
- Heaters, cleaned, tested and replaced as necessary.
- New die heater connnection panel.

For more details on 150 mm NRM PS and PP Extruder click here

Theysohn 3/4'' Single Screw Co-Extruder

- Approximate 20 to 1 L/D ratio.
- Electrically heated, air cooled 3 zone non-vented barrel.
- Water cooled feed throat with hopper.
- Driven by a 2 hp, 530 volt, 1750 rpm DC motor through a redducer, no ratio.

For more details on Theysohn 3/4'' Single Screw Co-Extruder click here