6" Gloucester Extruder

Used 6" 30:1 Gloucester extruder model 266-01 having a six zone electrically heated, water cooled barrel at approximately a 42" centerline height. Gearbox is direct driven by a 400 hp Baldor DC motor with free standing Saftronics SCR control (SCR mfd.

For more details on 6" Gloucester Extruder click here

130mm Reifenhauser Co-Rotating Twin Screw Extruder

Model BT-2803-2-130-21VHFC
- Vented barrel, air cooled with 6 barrel zones
- Aluminum heaters
- Updated panel with Cal 9900 temperature controllers for 6 barrel zones
- Screen changer and die zonees
- 150HP DC motor with late model Mentor II drive
- 23.

For more details on 130mm Reifenhauser Co-Rotating Twin Screw Extruder click here

3.5" Davis Standard Extruder

Mark 5 Series, Model 35MV350
- 24:1 L/D
- 17.4/1 gearbox ratio
- Belt driven 60 HP AC motor with Allen Bradley drive
- Integrated control panel consisting of 4 barrel zones
- 2 dies zones, and 1 clamp zone
- Eurotherm 2208E temperature controllers
- Pressure transducer
- Clamp
- Approx.

For more details on 3.5" Davis Standard Extruder click here

4.5" Welex Extruder

- 30:1 L/D ratio
- Water cooled
- 200HP electrostat DC motor
- 200HP Mentor drive, S/N 1945, Model IRHV
- Temperature control panel consists of 5 barrel zones, 12 dies zones, and 1 pump zone, 1/1

For more details on 4.5" Welex Extruder click here

6" Sterling Extruder

Consisting of:
- 24:1 L/D ratio
- Air cooled barrel, vented and plugged
- 42" center line height
- 400 hp DC motor
- 1750 RPM, 500 Volts, 632 Amps
- Burton speed stat VI DC drive
- 7 Barber Co

For more details on 6" Sterling Extruder click here

4.5" HPM Extruder

4.5" HPM Extruder Model TM-3
- L/D ratio: 30:1
- 200 hp DC motor
- 5 barrel zones and 4 die zones
- Eurotherm controllers
- Dynisco 4.5" screen changer
- Water cooled
- Dimensions (L x W x H):: 185 x 41 x 83
- Approx.

For more details on 4.5" HPM Extruder click here

6" PTI Single Extruder for Nylon Fiber to Pellets

Extruder 6" single screw PTI 40:1 vented fiber conversion system
- Used in Nylon fiber conversion both 6 and 6/6
- Machine was producing nylon pellets from fiber at rates up to 1500pph
- Original ccost US$ 1,000,000 without installation or equipment only purchased in 2001
- Both barrel and screw are worn (Estimated cost to replace new US$ 77,000 and cost to rebuild current US$ 56,000)

A) PTI Extruder:
Extruder Model: 6000 Trident Series
- 6" single screw extruder with ram stuffer forcing material in feed throat
- 40:1 L/D or ratio of screw size to length
- Barrels are water cooled internal tubing stainless steel
- 9-barrel heating zones (not including screen changer and head/die heating zones)
- Was producing nylon pellets from fiber at rates up to 1800pph
- Controlled by PLC by Allen Bradley
- Motor: 500 hp, US electrical motors, 460 volts, motor speed 1750/1900 rpm input
- Gearbox: Flender Corp, speed reducer 17.

For more details on 6" PTI Single Extruder for Nylon Fiber to Pellets click here

4.5" Davis Standard / NRM Extruder

4.5" 32/1 Davis Standard/NRM model 4.5" PMIII 32/1 extruder
- Electrically heated, water cooled barrel.
- Gearbox has a 17.72:1 reduction ratio and is direct driven by a 250 hp DC motor.
- Eurotheerm digital screen changer and temperature controls.

For more details on 4.5" Davis Standard / NRM Extruder click here

4.5" Davis Standard Non-vented Extruder

Model: 450H, 34/1 L/D non-vented extruder
- Has 17.21/1 gearbox ratio with rating of 147 hp at 1.5 service factor at a screw rpm of 40.
- Has electrically heated, air cooled barrel, includes hopperr with color feeder, has temperature control panel with (HES), Eurotherm 808 instruments.

For more details on 4.5" Davis Standard Non-vented Extruder click here

3.5" Davis Standard Single Screw Extruder

Model: 3.5MV-350
- A driven by 60 hp AC motor 3/60/460V with AC variable speed inverter.
- Has electrically heated, 5 zoned air cooled barrel, 30/1 L/D includes temperature control panel with 5 barrrel zones and 3 die zones, Eurotherm 2208 instruments.

For more details on 3.5" Davis Standard Single Screw Extruder click here

APV Extruder

Type: MP2030
- Working hours: +/- 500 hours
- Screw: Twin screw, 30 mm
- L/D: L = 11D (330 mm)
- RPM: 500 RPM
- Including:
a. Feeder
b. Water cooled cooling plate


For more details on APV Extruder click here

Extruder for Recycling

- Gear box size: 12 1/2
- Motor: 25h H.P
- Screw: 90 mm
- 2 mixture: 24" & 15 H.P
- Cutter: Sada & 3 H.P
- Output: 50 kgs. per hour
- Water tank/panel


For more details on Extruder for Recycling click here

Used PTI 6" 28:1 Extruder

Used PTI model 6000 Trident series 6" 28:1 extruder having a 7-zone electrically heated air cooled barrel at approximately a 94" centerline height. Gearbox is a Flender model SZNS-390, has reduction rratio of 21.

For more details on Used PTI 6" 28:1 Extruder click here