2.5 inch Killion Extruder

Used 2.5" Killion extruder, model 7EM
- 24:1 L/D ratio, 20 hp
- Koellmann gearbox with 13.95:1 ratio
- 70 hp rating
- Air cooled barrel
- 3 barrel zones
- 6 Barber Colman temperature controls



For more details on 2.5 inch Killion Extruder click here

5 HP Genca Pedestal Extruder

Used 1.25" Genca Pedestal extruder model GV12500A00000-00 with tilt and swing
- 3 barrel zones
- 24:1 L/D
- Air cooled
- 5 hp AC motor with Yaskawa model GPD515/G5 drive
- Belt driven to 10:1 geear box ratio
- 8.

For more details on 5 HP Genca Pedestal Extruder click here

Screw Extruders for PVC Granule

We need a 2 screw extruder for PVC granule to produce;
- L/D: between 24 and 28
- Screw diameter: more then 150 mm
- Capacity: More the 1500 kg/h


For more details on Screw Extruders for PVC Granule click here

97mm Berstorff Ultra Torque Co-rot. Twin Screw Ext

Model: ZE90AX31DUT
- 97mm diameter intermeshing screws
- 31:1 L/D ratio
- Electrically heated
- Water cooled barrel
- Six sections: Four (4) closed, one (1) feed (open) and one (1) vacuum vent seection
- Gearbox has a reduction ratio of 5.

For more details on 97mm Berstorff Ultra Torque Co-rot. Twin Screw Ext click here

Berstorff ZE130A Twin Screw Extruder

Model: ZE130A x 28D
- Capacity 2.5 tons per hour
- 28:1 L/D
- 133 mm diameter co-rotating screws
- Max screw speed min 30 rpm, max 350 rpm.
- Electrically heated, water cooled.
- Includes gearrbox by 1000 KW (1500 hp) motor.

For more details on Berstorff ZE130A Twin Screw Extruder click here

170mm Coperion Werner & Pfleiderer Twin Screw Co-r

Model: ZSK-170 W-1750 5G
- Screw diameter: 170mm (7'')
- Screw length: 2500mm (100'')
- Screw speed: +/- 198 rpm
- L/D 14.7, co-rotating, electric heating on housing no. 2, 3, 4 and 5 (65.8 KW (888hp)),
- Motor DC 760 KW (1013 hp), 6000 Volt
- Without switchgear, used on DMD
- Floor space 14.

For more details on 170mm Coperion Werner & Pfleiderer Twin Screw Co-r click here

120mm Werner & Pfleiderer Twin Screw Extruder

ZSK 120 Werner & Pfleiderer twin screw plastic extruder (co-rotating)
- Motor 700 KW 1495 rpm, 380V/50 hz/3ph
- Machine was completely rebuilt in Germany during 2003 including gearbox and all
electtrics / Siemens PLC control.

For more details on 120mm Werner & Pfleiderer Twin Screw Extruder click here

6" Gloucester Extruder

Used 6" 30:1 Gloucester extruder model 266-01 having a six zone electrically heated, water cooled barrel at approximately a 42" centerline height. Gearbox is direct driven by a 400 hp Baldor DC motor with free standing Saftronics SCR control (SCR mfd.

For more details on 6" Gloucester Extruder click here

Welding Engineers Twin Screw Co-rotating Extruder

Model: HT30MM (rated 225psi at 650 Degree F)
- Non-intermeshing
- Screw diameter: 30mm (1.2")
- Barrels: 12- barrels 180mm (7") each (total length 2160mm or 85.25")
- L/D: 69/1
- Motor: 25 hp (noo controls or electrical)
- RPM's: 500
- Heating/cooling: Oil (heaters not included)
- Vented with 4 vents total: (2) automated self cleaning and (2) are atmospheric
- Liquid injection valves 2 (one each before self cleaning vent)
- Was used to produce Latex rubber.

For more details on Welding Engineers Twin Screw Co-rotating Extruder click here

6" Gloucester Extruder

Used 6" 30:1 Gloucester extruder model 266-01 having a six zone electrically heated, water cooled barrel at approximately a 42" centerline height. Gearbox is direct driven by a 400 hp Baldor DC motor with free standing Saftronics SCR control (SCR mfd.

For more details on 6" Gloucester Extruder click here

130mm Reifenhauser Co-Rotating Twin Screw Extruder

Model BT-2803-2-130-21VHFC
- Vented barrel, air cooled with 6 barrel zones
- Aluminum heaters
- Updated panel with Cal 9900 temperature controllers for 6 barrel zones
- Screen changer and die zonees
- 150HP DC motor with late model Mentor II drive
- 23.

For more details on 130mm Reifenhauser Co-Rotating Twin Screw Extruder click here

3.5" Davis Standard Extruder

Mark 5 Series, Model 35MV350
- 24:1 L/D
- 17.4/1 gearbox ratio
- Belt driven 60 HP AC motor with Allen Bradley drive
- Integrated control panel consisting of 4 barrel zones
- 2 dies zones, and 1 clamp zone
- Eurotherm 2208E temperature controllers
- Pressure transducer
- Clamp
- Approx.

For more details on 3.5" Davis Standard Extruder click here

4.5" Welex Extruder

- 30:1 L/D ratio
- Water cooled
- 200HP electrostat DC motor
- 200HP Mentor drive, S/N 1945, Model IRHV
- Temperature control panel consists of 5 barrel zones, 12 dies zones, and 1 pump zone, 1/1

For more details on 4.5" Welex Extruder click here

6" Sterling Extruder

Consisting of:
- 24:1 L/D ratio
- Air cooled barrel, vented and plugged
- 42" center line height
- 400 hp DC motor
- 1750 RPM, 500 Volts, 632 Amps
- Burton speed stat VI DC drive
- 7 Barber Co

For more details on 6" Sterling Extruder click here

4.5" HPM Extruder

4.5" HPM Extruder Model TM-3
- L/D ratio: 30:1
- 200 hp DC motor
- 5 barrel zones and 4 die zones
- Eurotherm controllers
- Dynisco 4.5" screen changer
- Water cooled
- Dimensions (L x W x H):: 185 x 41 x 83
- Approx.

For more details on 4.5" HPM Extruder click here

6" PTI Single Extruder for Nylon Fiber to Pellets

Extruder 6" single screw PTI 40:1 vented fiber conversion system
- Used in Nylon fiber conversion both 6 and 6/6
- Machine was producing nylon pellets from fiber at rates up to 1500pph
- Original ccost US$ 1,000,000 without installation or equipment only purchased in 2001
- Both barrel and screw are worn (Estimated cost to replace new US$ 77,000 and cost to rebuild current US$ 56,000)

A) PTI Extruder:
Extruder Model: 6000 Trident Series
- 6" single screw extruder with ram stuffer forcing material in feed throat
- 40:1 L/D or ratio of screw size to length
- Barrels are water cooled internal tubing stainless steel
- 9-barrel heating zones (not including screen changer and head/die heating zones)
- Was producing nylon pellets from fiber at rates up to 1800pph
- Controlled by PLC by Allen Bradley
- Motor: 500 hp, US electrical motors, 460 volts, motor speed 1750/1900 rpm input
- Gearbox: Flender Corp, speed reducer 17.

For more details on 6" PTI Single Extruder for Nylon Fiber to Pellets click here

4.5" Davis Standard / NRM Extruder

4.5" 32/1 Davis Standard/NRM model 4.5" PMIII 32/1 extruder
- Electrically heated, water cooled barrel.
- Gearbox has a 17.72:1 reduction ratio and is direct driven by a 250 hp DC motor.
- Eurotheerm digital screen changer and temperature controls.

For more details on 4.5" Davis Standard / NRM Extruder click here

4.5" Davis Standard Non-vented Extruder

Model: 450H, 34/1 L/D non-vented extruder
- Has 17.21/1 gearbox ratio with rating of 147 hp at 1.5 service factor at a screw rpm of 40.
- Has electrically heated, air cooled barrel, includes hopperr with color feeder, has temperature control panel with (HES), Eurotherm 808 instruments.

For more details on 4.5" Davis Standard Non-vented Extruder click here

3.5" Davis Standard Single Screw Extruder

Model: 3.5MV-350
- A driven by 60 hp AC motor 3/60/460V with AC variable speed inverter.
- Has electrically heated, 5 zoned air cooled barrel, 30/1 L/D includes temperature control panel with 5 barrrel zones and 3 die zones, Eurotherm 2208 instruments.

For more details on 3.5" Davis Standard Single Screw Extruder click here

APV Extruder

Type: MP2030
- Working hours: +/- 500 hours
- Screw: Twin screw, 30 mm
- L/D: L = 11D (330 mm)
- RPM: 500 RPM
- Including:
a. Feeder
b. Water cooled cooling plate


For more details on APV Extruder click here

Extruder for Recycling

- Gear box size: 12 1/2
- Motor: 25h H.P
- Screw: 90 mm
- 2 mixture: 24" & 15 H.P
- Cutter: Sada & 3 H.P
- Output: 50 kgs. per hour
- Water tank/panel


For more details on Extruder for Recycling click here

Used PTI 6" 28:1 Extruder

Used PTI model 6000 Trident series 6" 28:1 extruder having a 7-zone electrically heated air cooled barrel at approximately a 94" centerline height. Gearbox is a Flender model SZNS-390, has reduction rratio of 21.

For more details on Used PTI 6" 28:1 Extruder click here

70 mm Werner & Pfleiderer Twin Screw Extruder

Werner & Pfleiderer 70 mm 32:1 300 HP twin screw extruder
MODEL ZSK70
- 600 RPM, 9 barrel sections with side feeder.
- 300 HP Reliance 460V AC forced vent motor.
- ZSN-70 side feeder. Strand die head, control panel.

For more details on 70 mm Werner & Pfleiderer Twin Screw Extruder click here

90 mm Werner & Pfleiderer Twin Screw Extruder

Werner & Pfleiderer 90mm 32:1 vented 250 HP
Model Number: ZSK 90
- Allen Bradley PLC control panel.
- 8 heat zones, water cooled with closed loop cooling system.
- 2 sets of screws. Co rotating, intermeshing screws.

For more details on 90 mm Werner & Pfleiderer Twin Screw Extruder click here

W & P 133mm Twin Screw Extruder

Used Coperion Werner & Pfleiderer twin screw extruder, type ZSK-133-M151000. Capacity 4 tons per hour. 27:1 L/D. 133 mm diameter x 3571 mm long screws. Co-rotating. Max screw speed 400 rpm. Electricallly heated, water cooled.

For more details on W & P 133mm Twin Screw Extruder click here

Berstorff Twin Screw Extruders

Used Berstorff 130mm twin screw extruder, type ZE130A x 28D, under 10 years, capacity 2.5 tons per hour. 28:1 L/D. 133 mm diameter screws. Co-rotating. Max. screw speed min 30 rpm, max 350 rpm. Electrrically heated, water cooled.

For more details on Berstorff Twin Screw Extruders click here

Buss Extruders

Buss Extruder (1)
- Brand: Buss
- Type: PLK100
- Year: 1987
- Screw: Single screw, 100 mm
- L/D: L = 7D (900 mm)
- Screw RPM: 50-300 RPM
- Engine: Piller, 17.5-77 kw, 500-2200 RPM
- Including::
a.

For more details on Buss Extruders click here

APV Extruder

- Type: MP2080
- Year of building: 1990
- Screw: Twin screw, 77 mm
- L/D: L = 16D (1232 mm)
- Screw RPM: 50-350 RPM
- Engine: 115 kW, 1.750 RPM
- Capacity: Up to 1.250 kg/hour
- Heating zones: 5
- Cooling: Water cooled
- Including:
a.

For more details on APV Extruder click here

Entek 73 mm Twin Screw Extruder

Used Entek model Emax 73 mm extruder having (2) co-rotating intermeshing screws. Extruder consists of twelve barrel sections and is electrically heated and water cooled. Includes two vacuum stuffers aand two (2) 70 mm side feeders.

For more details on Entek 73 mm Twin Screw Extruder click here

10 inch Hartig Non-vented Extruder

Used 10" Hartig 37/1 L/D non-vented extruder. - Electrically heated water cooled barrel with cast aluminum heaters.
- Equipped with a Wilson gearbox model D4545, rated at 800 hp at 1150 rpm input wiith 17.

For more details on 10 inch Hartig Non-vented Extruder click here

PVC Granular

PVC granular single screw.
- Size: 110 mm
- Production: 120-125 kgs per hour


For more details on PVC Granular click here